Entrpellung implementiert – noch nicht getestet

Signed-off-by: Stephan Richter <s.richter@srsoftware.de>

README.md

@@ -2,3 +2,4 @@
 |-------|------------------|-----------------|---------|---------|
 | 1.0   |               D2 |              D3 |      U7 |      U8 |
 | 2.0   |               D2 |            (D10)|      U8 |      U7 |
+| 2.1   |               D3 |              D2 |      U8 |      U7 | 

Software/BiDi/BiDi.ino

@@ -1,95 +0,0 @@
-/* RS 485-Implementierung, die sowohl Schreiben als auch Lesen kann */
-/* Basis für andere Projekte */
-
-#define BUTTON 2
-#define RECEIVE 3
-#define RECEIVE_ENABLE 4
-#define SEND 5
-#define SEND_ENABLE 6
-
-#define MAX_LEN 128
-
-void setup() {
-  // Buttons connected to analog input lines
-  pinMode(A0,INPUT_PULLUP);
-  pinMode(A1,INPUT_PULLUP);
-  pinMode(A2,INPUT_PULLUP);
-  pinMode(A3,INPUT_PULLUP);
-  pinMode(A4,INPUT_PULLUP);
-  pinMode(A5,INPUT_PULLUP);
-  pinMode(A6,INPUT_PULLUP);
-  pinMode(A7,INPUT_PULLUP);
-  // Currently, all buttons are also connected via a diode to an interruptable pin, to notify on input changes.
-  // This interruptable pin should be assgined to BUTTON
-  pinMode(BUTTON,INPUT_PULLUP);
-  attachInterrupt(digitalPinToInterrupt(BUTTON),button,FALLING); // interrupt for button change
-
-  // Set up pins for RS485 connection
-  pinMode(RECEIVE, INPUT);
-  pinMode(RECEIVE_ENABLE, OUTPUT);
-  pinMode(SEND, OUTPUT);
-  pinMode(SEND_ENABLE, OUTPUT);
-  attachInterrupt(digitalPinToInterrupt(RECEIVE),receive,CHANGE); // interrupt for incoming RS485 traffic
-  
-  reset485();
-  buttons = 0x0;
-}
-
-void button() {
-  buttons = 0xFF ^ (digitalRead(A7)<<7 | digitalRead(A6)<<6 | digitalRead(A5)<<5 | digitalRead(A4)<<4 | digitalRead(A3)<<3 | (!digitalRead(A2))<<2 | digitalRead(A1)<<1 | digitalRead(A0));  
-}
-
-void receive(){
-  bool received_bit = digitalRead(RECEIVE);
-  curr = micros();
-  duration = curr - last;
-  Serial.print("Input switched to ");
-  Serial.print(received_bit?"H":"L");  
-  Serial.print(" after ");
-  Serial.print(duration);
-  Serial.println(" ticks");
-  last = curr;
-  if (duration > MAX_TICKS) reset485();
-  received_bit = !received_bit; // received_bit is the current value, the duration of the previous value (=inverted) has been measured
-  duration /= BASE;
-  while (duration > 0){
-    byte_idx--;
-    recv |= received_bit<<byte_idx;
-    if (byte_idx == 0) {
-      msg[msg_idx] = recv;
-      msg_idx++;
-      byte_idx = 8;
-      if (recv == 0x00) message_received();
-    }
-    duration--;
-  }
-}
-
-void reset485(){
-  byte_idx = 8;
-  msg_idx = 0;
-  recv=0x0;
-}
-
-void message_received(){
-  for (int i=0; i<MAX_LEN; i++) message[i]=msg[i];
-  reset485();
-}
-
-void button_pressed(int i){
-  Serial.println("not implemented");
-}
-
-void loop(){
-  if (buttons>0){
-    for (int i=0; i<7; i++){
-      if (buttons & (1<<i)) button_pressed(i);     
-    }    
-  }
-  if (message[0] != 0x0){
-    Serial.print("Received '");
-    Serial.print(message);
-    Serial.println("'");    
-    message[0] = 0x0;
-  }
-}

Software/LCDReceiver/LCDReceiver.ino

@@ -9,48 +9,47 @@
 #include <LiquidCrystal.h>
 #include <SoftRS485.h>
 
-#define PROGRAM "RS485-Nano Rev 2.0 / LCDReceive 1.2"
+#define Max485_RO 2 // read-output of Max485
+#define Max485_RE 8 // not-read-enable of Max485
+#define Max485_DE 8 // data enable of Max485
+#define Max485_DI 9 // data input of Max485
 
-#define Max485_RO 3 // read-output of Max485
+#define LCD_RS 10
-#define Max485_RE 5 // not-read-enable of Max485
+#define LCD_EN 11
-#define Max485_DE 9 // data enable of Max485
+#define LCD_D4 4
-#define Max485_DI 8 // data input of Max485
+#define LCD_D5 5
+#define LCD_D6 6
+#define LCD_D7 7
+
+#define PROGRAM "RS485-Nano 2.1 / LCDReceive 1.2"
 
-#define LCD_RS 4
-#define LCD_EN 6
-#define LCD_D4 7
-#define LCD_D5 11
-#define LCD_D6 12
-#define LCD_D7 13
 
 // initialize the library by associating any needed LCD interface pin with the arduino pin number it is connected to
 LiquidCrystal lcd(LCD_RS, LCD_EN, LCD_D4, LCD_D5, LCD_D6, LCD_D7);
 
+
 void setup() {
   Serial.begin(115200);
   init485(Max485_RO,Max485_RE,Max485_DE,Max485_DI); // library initialization:
+  invert485polarity(true);
   // set up the LCD's number of columns and rows:
   lcd.begin(16, 2);
   // Print a message to the LCD.
   printMessage(PROGRAM);
+
 }
 
 void printMessage(String s){
     Serial.println(s);
-    lcd.clear();    
+    lcd.clear();
-    int line = 0;
+    lcd.setCursor(0, 0);
-    int col = 0;
+    lcd.print(s);
-    auto cstr = s.c_str();
+    if (s.length()>16) {
-    for (int i=0;i<s.length();i++){
+      lcd.setCursor(0, 1);
-      if (col == 0 && cstr[i] == ' ') continue;
+      s=s.substring(16);
-      lcd.print(cstr[i]);
+      s.trim();
-      col++;
+      lcd.print(s);
-      if (cstr[i]==',' || col==16){
+    }  
-        line++;
-        col=0;
-        lcd.setCursor(col, line);
-      }
-    }
 }
 
 void loop() {

Software/Receiver/Receiver.ino

@@ -1,61 +0,0 @@
-// Für Controllino könnte man benutzen: sRx = 20, sTx = 21, enable = 53
-
-int sTx = 2;
-int sRx = 3;
-
-long base = 100;
-long rst = base*10; // reset
-boolean bt = false;
-long dif = 0;
-long lt = 0;
-long now = 0;
-char rcv = 0;
-int idx = 0;
-String message;
-void setup(){
-  pinMode(sRx,INPUT);
-  pinMode(sTx,OUTPUT);
-  attachInterrupt(digitalPinToInterrupt(sRx),change485,CHANGE);
-  Serial.begin(115200);  
-  Serial.println("Receiver ready");
-}
-
-void reset485(long dif){
-    rcv = 0;
-    idx = -1;
-    message.reserve(32);
-}
-void change485(){
-  bool bt = digitalRead(sRx);
-  now = micros();
-  dif = now - lt;
-  lt = now;
-  if (dif > rst){
-    reset485(dif);
-  } else {
-    handle485(!bt,dif);
-  }
-}
-
-void handle485(boolean bt, long dif){
-  long count = dif/base;
-  for (int i=0; i<count; i++) push485(bt);
-}
-
-void push485(boolean bt){
-  if (idx>=0) rcv |= bt<<idx;
-  idx++;
-  
-  if (idx == 8){
-    if (rcv == 13) {
-      Serial.println(message);
-      message = "";
-    } else {
-      message+=rcv;
-    } 
-    idx =0;
-    rcv =0;
-  }
-}
-
-void loop(){}

Software/Sender/Sender.ino

@@ -9,31 +9,24 @@
 // include the library code:
 #include <SoftRS485.h>
 
-// 0=Test
+#define PROGRAM "RS485-Nano 2.1 / Sender 1.1"
-// 1=Flur
-// 2=Wohnzimmer
-// 3=Bad EG
-// 4=Treppenhaus
-// 5=Arbeitszimmer
-// 6=Bad OG
 
+#define BTN_INT 3 // button interrupt pin
+#define Max485_RO 2 // read-output of Max485
+#define Max485_RE 3 // not-read-enable of Max485
+#define Max485_DE 8 // data enable of Max485
+#define Max485_DI 9 // data input of Max485
+
+#define TRESHOLD 100
 #define ID 0
-#define PROGRAM "Sender"
+// 0=Test
-#define SW_VERSION "1.3"
+// 1=Arbeitszimmer
-#define HW_VERSION "2.0"
+// 2=Küche
+// 3=Bad
 
-#define BTN_INT 2 // button interrupt pin
-#define Max485_RO 3 // read-output of Max485
-#define Max485_RE 5 // not-read-enable of Max485
-#define Max485_DE 9 // data enable of Max485
-#define Max485_DI 8 // data input of Max485
-
-#define TRESHOLD 1024
-#define TRIGGER_LEVEL 200
-
-//#define DEBUG
 //#define LOG_TO_SERIAL
 #define SEND_485
+#define DEBUG
 
 boolean raw_states[8];
 boolean states[8];
@@ -60,54 +53,56 @@ void setup(){
   pinMode(20,INPUT_PULLUP);
   pinMode(21,INPUT_PULLUP);
 
-  attachInterrupt(digitalPinToInterrupt(BTN_INT),isr,CHANGE);
+  attachInterrupt(digitalPinToInterrupt(2),isr,CHANGE);
-  String s = "{nano:"+String(ID)+",hw:"+HW_VERSION+","+PROGRAM+":"+SW_VERSION+"}";
+  // Print a message to the LCD.
-  Serial.println(s);
+  Serial.println(PROGRAM);
-  send485(s.c_str());
 #ifdef LOG_TO_SERIAL
   Serial.println("14 15 16 17 18 19 20 21");
 #endif
 }
 
 void isr(){
-  raw_states[0] = analogRead(14)<TRIGGER_LEVEL;
+  raw_states[0] = !digitalRead(14);
-  raw_states[1] = analogRead(15)<TRIGGER_LEVEL;
+  raw_states[1] = !digitalRead(15);
-  raw_states[2] = analogRead(16)<TRIGGER_LEVEL;
+  raw_states[2] = !digitalRead(16);
-  raw_states[3] = analogRead(17)<TRIGGER_LEVEL;
+  raw_states[3] = !digitalRead(17);
 
-  raw_states[4] = analogRead(18)<TRIGGER_LEVEL;
+  raw_states[4] = !digitalRead(18);
-  raw_states[5] = analogRead(19)<TRIGGER_LEVEL;
+  raw_states[5] = !digitalRead(19);
-  raw_states[6] = analogRead(20)<TRIGGER_LEVEL;
+  raw_states[6] = !(analogRead(20)>400);
-  raw_states[7] = analogRead(21)<TRIGGER_LEVEL;
+  raw_states[7] = !(analogRead(21)>400);
 #ifdef LOG_TO_SERIAL
   for (int i=0;i<8;i++){
-    Serial.print(" ");    
+    Serial.print(" "); Serial.print(raw_states[i]); Serial.print(" ");
-    Serial.print(raw_states[i]);
-    Serial.print(" ");
   }
   Serial.println();
 #endif
 }
 
-void send(int btn, long duration){
-  String s = "{nano:"+String(ID)+",btn:"+String(btn)+",ms:"+String(duration)+"}";
 #ifdef SEND_485
+void send(int btn, long duration){
+  String s = "{nano:"+String(ID)+",btn:"+String(btn)+",dura:"+String(duration)+"}";
   for (int i = 0; i<10; i++){
     if (send485(s.c_str())) break;
     Serial.println("collision detected, trying again:");
   }
-#else
-  Serial.println(s);
-#endif
 }
+#endif
 
 void loop(){
   unsigned long now = micros();
+  boolean pause = true;
   for (int i=0;i<8;i++){
     // we emulate a capacitor:
     // when the button is pressed, it slowly loads, if the button is released, it unloads.
     capacitor[i] = raw_states[i] ? capacitor[i]+1 : capacitor[i]>>1;
 
+#ifdef DEBUG
+    if (capacitor[i]) {
+      Serial.print("cap "); Serial.print(i); Serial.print(": "); Serial.println(capacitor[i]);
+    }
+#endif    
+
     // if the capacitor reaches a certain treshold, the state is changed
     boolean new_state = capacitor[i]>TRESHOLD;
 
@@ -115,9 +110,13 @@ void loop(){
 
     // when the state changes, the duration of the last state is calculated
     if (states[i] != new_state){      
-      long diff = (now - times[i])/1000;
+      long diff = now - times[i];
       times[i] = now;
-      if (states[i]) send(i+1,diff); // old state was HIGH → we are going LOW
+#ifdef SEND_485
+      if (states[i]){ // old state was HIGH → we are going LOW
+        send(i+1,diff);
+      }
+#endif      
       states[i] = new_state;
     }
   }

Software/SerialTransceiver/SerialTransceiver.ino

@@ -1,37 +0,0 @@
-/*
- *  Demonstrates how to use LCDisplay in conjunction with SoftRS485:
- *
- *  The main _loop_ of this program listens on the RS485 bus.
- *  Whenever a message is received from the bus, it is displayed on the LCD.
- */
-
-// include the library code:
-#include <SoftRS485.h>
-
-#define Max485_RO 3 // read-output of Max485
-#define Max485_RE 5 // not-read-enable of Max485
-#define Max485_DE 9 // data enable of Max485
-#define Max485_DI 8 // data input of Max485
-
-#define PROGRAM "{hw:RS485-Nano rev 2.0,firmware:Transceiver,version:1.0}"
-
-String message = "";
-char c;
-void setup() {
-  Serial.begin(115200);
-  init485(Max485_RO,Max485_RE,Max485_DE,Max485_DI); // library initialization:
-  send485(PROGRAM);
-}
-
-void loop() {
-  if (available485()) Serial.println(get485message());
-  while (Serial.available()) {
-    c = (char)Serial.read();
-    if (c == '\n') {
-      send485(message.c_str());
-      message = "";
-    } else {
-      message += c;    
-    }
-  }  
-}

Software/TempSender/TempSender.ino

@@ -4,61 +4,41 @@
  * If a button is pressed, a corresponding flag is set.
  * The main loop checks for the state of those flags and
  * sends a message on the RS485 bus whenever a flag is set.
- * 
- * Additionally, the temperature is read from a DHT22 sensor once per minute
  */
 
 // include the library code:
 #include <SoftRS485.h>
-#include <SimpleDHT.h>
+#include <AM2302-Sensor.h>
 
-// 0=Test
+#define PROGRAM "RS485-Nano 2.1 / TempSender 1.1"
-// 1=Flur
-// 2=Wohnzimmer
-// 3=Bad EG
-// 4=Treppenhaus
-// 5=Arbeitszimmer
-// 6=Bad OG
-
-#define ID 5
-#define PROGRAM "TempSender"
-#define SW_VERSION "1.5"
-#define HW_VERSION "2.0"
-
-#define BTN_INT 2 // button interrupt pin
-#define Max485_RO 3 // read-output of Max485
-#define Max485_RE 5 // not-read-enable of Max485
-#define Max485_DE 9 // data enable of Max485
-#define Max485_DI 8 // data input of Max485
-
-#define TRESHOLD 1024
-#define TRIGGER_LEVEL 200
 
+#define BTN_INT 3 // button interrupt pin
+#define Max485_RO 2 // read-output of Max485
+#define Max485_RE 3 // not-read-enable of Max485
+#define Max485_DE 8 // data enable of Max485
+#define Max485_DI 9 // data input of Max485
 #define DHT_PIN 4
+#define TRESHOLD 100000 // 100ms
 #define PERIOD   100000000 // 100s
+#define ID 3
+// 0=Test
+// 1=Arbeitszimmer
+// 2=Küche
+// 3=Bad
 
-//#define DEBUG
 //#define LOG_TO_SERIAL
 #define SEND_485
 
-boolean raw_states[8];
+AM2302::AM2302_Sensor am2302{DHT_PIN};
-boolean states[8];
+
-unsigned long capacitor[8];
+boolean states[8];
-unsigned long times[8];
+unsigned long times[8];
-unsigned long sensor_time = 0;
+unsigned long sensor_time = PERIOD;
 
-SimpleDHT22 sensor(DHT_PIN);
-float temperature = 0;
-float humidity = 0;
-int err = SimpleDHTErrSuccess;
 
 void setup(){
-  for (int i=0; i<8;i++) {
-    capacitor[i] = 0;
-    raw_states[i] = LOW;
-    states[i] = LOW;
-  }
   Serial.begin(115200);
+  am2302.begin();
   init485(Max485_RO,Max485_RE,Max485_DE,Max485_DI); // library initialization:
   pinMode(BTN_INT,INPUT_PULLUP);
   pinMode(14,INPUT_PULLUP);
@@ -70,74 +50,67 @@ void setup(){
   pinMode(20,INPUT_PULLUP);
   pinMode(21,INPUT_PULLUP);
 
-  attachInterrupt(digitalPinToInterrupt(BTN_INT),isr,CHANGE);
+  attachInterrupt(digitalPinToInterrupt(2),isr,FALLING);
-  String s = "{nano:"+String(ID)+",hw:"+HW_VERSION+","+PROGRAM+":"+SW_VERSION+"}";
+  // Print a message to the LCD.
-  Serial.println(s);
+  Serial.println(PROGRAM);
-  send485(s.c_str());
 #ifdef LOG_TO_SERIAL
   Serial.println("14 15 16 17 18 19 20 21");
 #endif
 }
 
 void isr(){
-  raw_states[0] = analogRead(14)<TRIGGER_LEVEL;
+  states[0] = !digitalRead(14);
-  raw_states[1] = analogRead(15)<TRIGGER_LEVEL;
+  states[1] = !digitalRead(15);
-  raw_states[2] = analogRead(16)<TRIGGER_LEVEL;
+  states[2] = !digitalRead(16);
-  raw_states[3] = analogRead(17)<TRIGGER_LEVEL;
+  states[3] = !digitalRead(17);
 
-  raw_states[4] = analogRead(18)<TRIGGER_LEVEL;
+  states[4] = !digitalRead(18);
-  raw_states[5] = analogRead(19)<TRIGGER_LEVEL;
+  states[5] = !digitalRead(19);
-  raw_states[6] = analogRead(20)<TRIGGER_LEVEL;
+  states[6] = !(analogRead(20)>200);
-  raw_states[7] = analogRead(21)<TRIGGER_LEVEL;
+  states[7] = !(analogRead(21)>200);
 #ifdef LOG_TO_SERIAL
   for (int i=0;i<8;i++){
-    Serial.print(" ");    
+    Serial.print(" "); Serial.print(states[i]); Serial.print(" ");
-    Serial.print(raw_states[i]);
-    Serial.print(" ");
   }
   Serial.println();
 #endif
 }
 
-void send(int btn, long duration){
-  String s = "{nano:"+String(ID)+",btn:"+String(btn)+",ms:"+String(duration)+"}";
 #ifdef SEND_485
+void send(int btn){
+  String s = "{nano:"+String(ID)+",btn:"+String(btn)+"}";
   for (int i = 0; i<10; i++){
     if (send485(s.c_str())) break;
     Serial.println("collision detected, trying again:");
   }
-#else
-  Serial.println(s);
-#endif
 }
+#endif
 
 void loop(){
   unsigned long now = micros();
   for (int i=0;i<8;i++){
-    // we emulate a capacitor:
+    if (states[i]){
-    // when the button is pressed, it slowly loads, if the button is released, it unloads.
+      delay(1);
-    capacitor[i] = raw_states[i] ? capacitor[i]+1 : capacitor[i]>>1;
+      if (now - times[i] > TRESHOLD){
-
+#ifdef SEND_485
-    // if the capacitor reaches a certain treshold, the state is changed
+        send(i+1);
-    boolean new_state = capacitor[i]>TRESHOLD;
+#endif
-
+        times[i] = now;
-    // TODO: drop state after a maximum HIGH time
+      }
-
+      states[i] = 0;
-    // when the state changes, the duration of the last state is calculated
-    if (states[i] != new_state){      
-      long diff = (now - times[i])/1000;
-      times[i] = now;
-      if (states[i]) send(i+1,diff); // old state was HIGH → we are going LOW
-      states[i] = new_state;
     }
   }
 
   if (now - sensor_time > PERIOD){
     sensor_time = now;
-    if ((err = sensor.read2(&temperature, &humidity, NULL)) == SimpleDHTErrSuccess) {
+    auto status = am2302.read();
-      String s = "{nano:"+String(ID)+",temp:"+String(temperature,1)+",humi:"+String(humidity,1)+"}";
+    if (status == 0){
-      Serial.println(s);
+      String s = "{nano:"+String(ID)+",temp:"+String(am2302.get_Temperature())+",humi:"+String(am2302.get_Hunidity())+"}";
       send485(s.c_str());
+#ifdef LOG_TO_SERIAL
+      Serial.println(s);
+#endif
     }
   }
+  
 }

Software/TempSenderPlusIR/TempSenderPlusIR.ino

@@ -1,194 +0,0 @@
-/*
- *  Demonstrates how to use Read Buttons in conjunction with SoftRS485:
- *
- * If a button is pressed, a corresponding flag is set.
- * The main loop checks for the state of those flags and
- * sends a message on the RS485 bus whenever a flag is set.
- * 
- * Additionally, the temperature is read from a DHT22 sensor once per minute
- */
-
-// include the library code:
-#include <SoftRS485.h>
-#include <SimpleDHT.h>
-#include <TinyIRSender.hpp>
-
-// 0=Test
-// 1=Flur
-// 2=Wohnzimmer
-// 3=Bad EG
-// 4=Treppenhaus
-// 5=Arbeitszimmer
-// 6=Bad OG
-
-#define ID 0
-#define PROGRAM "Temp+IR"
-#define SW_VERSION "0.1"
-#define HW_VERSION "2.0"
-
-#define BTN_INT 2 // button interrupt pin
-#define Max485_RO 3 // read-output of Max485
-#define Max485_RE 5 // not-read-enable of Max485
-#define Max485_DE 9 // data enable of Max485
-#define Max485_DI 8 // data input of Max485
-
-#define TRESHOLD 1024
-#define TRIGGER_LEVEL 200
-
-#define DHT_PIN 4
-#define PERIOD   100000000 // 100s
-
-#define IR_PIN 5
-#define REPEATS 2
-
-//#define DEBUG
-//#define LOG_TO_SERIAL
-#define SEND_485
-
-boolean raw_states[8];
-boolean states[8];
-unsigned long capacitor[8];
-unsigned long times[8];
-unsigned long sensor_time = 0;
-
-// these values are used for temperature processing
-SimpleDHT11 sensor(DHT_PIN);
-byte temperature = 0;
-byte humidity = 0;
-int err = SimpleDHTErrSuccess;
-
-// these constants are used for message parsing in handle(message)
-const char* outer_delimiter = "{,}";
-const char* inner_delimiter = ":";
-
-void setup(){
-  for (int i=0; i<8;i++) {
-    capacitor[i] = 0;
-    raw_states[i] = LOW;
-    states[i] = LOW;
-  }
-  Serial.begin(115200);
-  init485(Max485_RO,Max485_RE,Max485_DE,Max485_DI); // library initialization:
-  pinMode(BTN_INT,INPUT_PULLUP);
-  pinMode(14,INPUT_PULLUP);
-  pinMode(15,INPUT_PULLUP);
-  pinMode(16,INPUT_PULLUP);
-  pinMode(17,INPUT_PULLUP);
-  pinMode(18,INPUT_PULLUP);
-  pinMode(19,INPUT_PULLUP);
-  pinMode(20,INPUT_PULLUP);
-  pinMode(21,INPUT_PULLUP);
-
-  attachInterrupt(digitalPinToInterrupt(BTN_INT),isr,CHANGE);
-  String s = "{nano:"+String(ID)+",hw:"+HW_VERSION+","+PROGRAM+":"+SW_VERSION+"}";
-  Serial.println(s);
-  send485(s.c_str());
-#ifdef LOG_TO_SERIAL
-  Serial.println("14 15 16 17 18 19 20 21");
-#endif
-}
-
-void isr(){
-  raw_states[0] = analogRead(14)<TRIGGER_LEVEL;
-  raw_states[1] = analogRead(15)<TRIGGER_LEVEL;
-  raw_states[2] = analogRead(16)<TRIGGER_LEVEL;
-  raw_states[3] = analogRead(17)<TRIGGER_LEVEL;
-
-  raw_states[4] = analogRead(18)<TRIGGER_LEVEL;
-  raw_states[5] = analogRead(19)<TRIGGER_LEVEL;
-  raw_states[6] = analogRead(20)<TRIGGER_LEVEL;
-  raw_states[7] = analogRead(21)<TRIGGER_LEVEL;
-#ifdef LOG_TO_SERIAL
-  for (int i=0;i<8;i++){
-    Serial.print(" ");    
-    Serial.print(raw_states[i]);
-    Serial.print(" ");
-  }
-  Serial.println();
-#endif
-}
-
-void send(int btn, long duration){
-  String s = "{nano:"+String(ID)+",btn:"+String(btn)+",ms:"+String(duration)+"}";
-#ifdef SEND_485
-  for (int i = 0; i<10; i++){
-    if (send485(s.c_str())) break;
-    Serial.println("collision detected, trying again:");
-  }
-#else
-  Serial.println(s);
-#endif
-}
-
-
-
-
-void handle(String message){
-#ifdef LOG_TO_SERIAL
-  Serial.println(message);
-#endif   
-  unsigned int ir_cmd = 0;
-  unsigned int ir_addr = 0;
-  unsigned int nano = 0;
-
-  const char* outer_state = NULL;
-  const char* inner_state = NULL;  
-  char* token = strtok_r(message.c_str(), outer_delimiter, &outer_state);
-  
-  while (token != NULL) {    
-    char* key = strtok_r(token,inner_delimiter,&inner_state);
-    char* val = strtok_r(NULL,inner_delimiter,&inner_state);
-    if (strcmp(key,"nano")==0) nano = atoi(val);      
-    if (strcmp(key,"addr")==0) ir_addr = atoi(val);
-    if (strcmp(key,"ir")==0) ir_cmd = atoi(val);
-    token=strtok_r(NULL, outer_delimiter, &outer_state);
-  }
-  
-  if (nano == ID){ // the message is addressed to us!
- 
-    if (ir_addr && ir_cmd){
-#ifdef LOG_TO_SERIAL
-      Serial.print("Sending 0x");
-      Serial.print(ir_cmd,HEX);
-      Serial.print(" to 0x");
-      Serial.println(ir_addr,HEX);
-#endif
-      sendNECMinimal(IR_PIN, ir_addr, ir_cmd, REPEATS);
-     }
-  }
-}
-
-void loop(){
-  unsigned long now = micros();
-  for (int i=0;i<8;i++){
-    // we emulate a capacitor:
-    // when the button is pressed, it slowly loads, if the button is released, it unloads.
-    capacitor[i] = raw_states[i] ? capacitor[i]+1 : capacitor[i]>>1;
-
-    // if the capacitor reaches a certain treshold, the state is changed
-    boolean new_state = capacitor[i]>TRESHOLD;
-
-    // TODO: drop state after a maximum HIGH time
-
-    // when the state changes, the duration of the last state is calculated
-    if (states[i] != new_state){      
-      long diff = (now - times[i])/1000;
-      times[i] = now;
-      if (states[i]) send(i+1,diff); // old state was HIGH → we are going LOW
-      states[i] = new_state;
-    }
-  }
-
-  if (now - sensor_time > PERIOD){
-    sensor_time = now;
-    if ((err = sensor.read(&temperature, &humidity, NULL)) == SimpleDHTErrSuccess) {
-      String s = "{nano:"+String(ID)+",temp:"+String((int)temperature)+",humi:"+String((int)humidity)+"}";
-#ifdef LOG_TO_SERIAL
-      Serial.println(s);
-#endif
-      send485(s.c_str());
-    }
-  }
-  
-  if (available485()) handle(get485message());
-}